On 12 Jan 2006 at 19:06, Bruno Robichaud <[log in to unmask]> wrote:
> This is what I use to test , thx again Francoise :)
How are you sending the DISTRIBUTE job to LISTSERV? Are you sending
an email to LISTSERV@yourdomain or are you using the file drop-in
method described here in the "Feed Custom Messages" White Paper at
http://www.lsoft.com/resources/wp-feed-smtp.pdf ?
If you are sending the email to LISTSERV, you don't need the HELO
etc. If you're using the file-drop in to essentially have LISTSERV's
SMTP workers send mail to itself, then the RCPT TO and the To: need
to be LISTSERV@yourdomain and the From needs to be either a
POSTMASTER or DIST_ALLOWED_USER in the LISTSERV site configuration
(and the PW= refers to that address' password).
> // DISTRIBUTE MAIL-MERGE DBMS=YES(EMAIL=SenderAddress)[log in to unmask]
Needs a space between ) and FROM= and no // unless the DISTRIBUTE is
split over several lines, in which case it needs a "," at the end of
each line. The //<space> command , <CRLF>more command is the
continuation syntax.
Francoise
>
> -----Original Message-----
> From: LISTSERV site administrators' forum
> [mailto:[log in to unmask]] On Behalf Of Francoise Becker
> Sent: Thursday, January 12, 2006 7:00 PM
> To: [log in to unmask]
> Subject: Re: Bounced email
>
> On 12 Jan 2006 at 18:37, Bruno Robichaud <[log in to unmask]>
> wrote:
>
> > Yeah I try that because that what was show in the documentation founds on
> > LSoft Website but I'm getting a error telling me that it's didn't
> recognize
> > the function,
>
> I would have to see the actual email you sent to LISTSERV to diagnose
> this. I would suspect that your email client is wrapping the
> DISTRIBUTE command so that the FROM= is ending up on a different line
> than the DISTRIBUTE, but there could be some other syntax error.
> (This is why I strongly recommend Maestro, as it takes care of the
> syntax for you).
>
> > also if I use a another email to get the bounce that is not
> > LISTSERV related do I have to configure something specific?
>
> Well, the address has to exist (otherwise you'll be labeled as a
> spammer), but that's about it if you don't need LISTSERV to do your
> bounce processing for you.
>
> > My second question was how can I put the header for my email-merge job so
> > when user receive they emails, there a subject (like this one who said
> > Re:Bounced Email) I founded a pdf with all the information I needed in the
> > white paper where it's show that you have to right HELO and soo on but I
> try
> > it too and does work, I still can't see nothing in the subject.
>
> All the RFC822 headers such as Subject:, Date:, To:, and From: need
> to be defined in the DATA portion of the DISTRIBUTE job.
>
> I assume you're referring to the "Sending MIME Messages in
> LISTSERV(R) DISTRIBUTE Jobs" White Paper at:
>
> http://www.lsoft.com/resources/wp-mime-dist.pdf
>
> That only shows the DATA portion of the DISTRIBUTE job, not the whole
> DISTRIBUTE job. Section 3 of the LISTSERV Developer's manual
> describes the whole DISTRIBUTE job format. Note that the DISTRIBUTE
> command needs to be all on one line or else the continutation syntax
> needs to be used.
>
> --
> Francoise Becker <[log in to unmask]>
>
> Knowledge is just a click away: http://www.lsoft.com/optin.html
--
Francoise Becker <[log in to unmask]>
Knowledge is just a click away: http://www.lsoft.com/optin.html
|